Photo Etched Parts 1/16 Scale

Photo Etched Parts 1/16 Scale


Display per page
Sort by
1 - 30 of 31 results
Product no.: AT-16-100
On each plate there are two sand sheets. The sand sheets can be used for modeling and detailing of military trucks used in the scale 1:16.
$32.00 *
Delivery weight: 100 g


can be shipped within 14 days

Product no.: AT-16-101
$14.50 *
Delivery weight: 50 g


can be shipped within 14 days

Product no.: AT-16-103
$11.50 *
Delivery weight: 50 g


can be shipped within 14 days

Product no.: AT-16-104
MG not included. It is also 1 AFV MG3, model screws M0, 6 and model rivets 0.6 mm and a piece of brass pipe needed.
$17.50 *
Delivery weight: 50 g


can be shipped within 14 days

Product no.: AT-16-102
The plate includes 90 platform hooks. the hooks have to be bended and can be attached by using model rivets 0,5 mm or 0,6 mm. The hole spacing is 2,4 mm


can be shipped within 10 days

Product no.: MA-16-AT04
The plate includes 4 platform steps and can be attached by foldaway frames.
$37.40 *


can be shipped within 10 days

Product no.: MA-16-AT06


can be shipped within 10 days

Product no.: BA-16-01
6 Beret badges, 1:16 - Pioneers The badges have a size of about 3.4 mm x 2.7 mm, but many details are visible! The photo layer on the back of the badge should be worn, since the glue holds better. It is best to dab a small drop of superglue on the beret and placed the badge on it.
$5.50 *
Delivery weight: 20 g


can be shipped within 14 days

Product no.: BA-16-02
6 Beret badges, 1:16 - Sanitäter (medics) The badges have a size of about 3.4 mm x 2.7 mm, but many details are visible! The photo layer on the back of the badge should be worn, since the glue holds better. It is best to dab a small drop of superglue on the beret and placed the badge on it.
$5.50 *
Delivery weight: 20 g


can be shipped within 14 days

Product no.: BA-16-03
6 Beret badges, 1:16 - Artillery The badges have a size of about 3.4 mm x 2.7 mm, but many details are visible! The photo layer on the back of the badge should be worn, since the glue holds better. It is best to dab a small drop of superglue on the beret and placed the badge on it.
$5.50 *
Delivery weight: 20 g


can be shipped within 14 days

Product no.: BA-16-04
6 Beret badges, 1:16 - Military Police The badges have a size of about 3.4 mm x 2.7 mm, but many details are visible! The photo layer on the back of the badge should be worn, since the glue holds better. It is best to dab a small drop of superglue on the beret and placed the badge on it.
$5.50 *
Delivery weight: 20 g


can be shipped within 14 days

Product no.: BA-16-05
6 Beret badges, 1:16 - Paratroopers The badges have a size of about 3.4 mm x 2.7 mm, but many details are visible! The photo layer on the back of the badge should be worn, since the glue holds better. It is best to dab a small drop of superglue on the beret and placed the badge on it.
$5.50 *
Delivery weight: 20 g


can be shipped within 14 days

Product no.: FU-16-AT01

The plate includes the tool clambs for the transporting vehicle Fuchs. The clambs are designed for the use of the tools from AFV. It will need the following tools: two spades, 1 saw, one bolt cutters, 1 large ax, 1 small ax, 1 pickaxe

$44.00 *
Delivery weight: 80 g


can be shipped within 14 days

Product no.: BA-16-06
6 Beret badges, 1:16 - Armored Vehicles The badges have a size of about 3.4 mm x 2.7 mm, but many details are visible! The photo layer on the back of the badge should be worn, since the glue holds better. It is best to dab a small drop of superglue on the beret and placed the badge on it.
$5.50 *
Delivery weight: 20 g


can be shipped within 14 days

Product no.: GE-16-AT01
$44.00 *
Delivery weight: 80 g


can be shipped within 14 days

Product no.: BA-16-07
6 Beret badges, 1:16 - Infantry The badges have a size of about 3.4 mm x 2.7 mm, but many details are visible! The photo layer on the back of the badge should be worn, since the glue holds better. It is best to dab a small drop of superglue on the beret and placed the badge on it.
$5.50 *
Delivery weight: 20 g


can be shipped within 14 days

Product no.: LS-16-01
Painting stencils for tactical signs of the Bundeswehr in 1:16 scale. The stencils are etched in nickel silver 0.2 mm thick. In the lower left corner is a small arrow and at the bottom are two marks for alignment of the stencil, so that each of the left or right half can be painted. The easiest way is if you affix a stripe tabe below the stencil, attaches the stencil and fixe it with tape. Then make a small line in an extension of the left marker. After painting the left half, the stencil is shifted to the left until the right marker is in line with the line on the tape. Now the right half can be painted. In this way, the tactical sign are built up step by step.
$29.00 *
Delivery weight: 50 g


can be shipped within 14 days

Product no.: WI-16-AT01
$65.00 *
Delivery weight: 120 g


can be shipped within 14 days

Product no.: WI-16-AT02
$65.00 *
Delivery weight: 120 g


can be shipped within 14 days

Product no.: WI-16-AT03
$29.00 *
Delivery weight: 80 g


can be shipped within 14 days

Product no.: WI-16-AT04
$29.00 *
Delivery weight: 80 g


can be shipped within 14 days

Product no.: LE-16-AT03

The plate includes all tool clamps for the Bergepanzer Leopard 1. For using the clamps at Tamiya Leopard 1 Kit the plastic clamps have to be removed carefully. For connecting ant attaching the parts to the model you can use model screws M0,6 and rivets 0,6mm. By using the clamps at RC-models we recommend the soldering of the photo etched parts. Round about 60 screws M0,6 and 50 rivets 0,6mm are neccessary.

$46.00 *
Delivery weight: 0.1 kg


can be shipped within 14 days

Product no.: LE-16-AT01

The plate include als tool clamps for the Leopard 2. For using the clamps at Tamiya Leopard 2 Kit the plastic clamps have to be removed carefully. For using the clamps at models of Peter Müller, it can be attached directly . For connecting ant attaching the parts to the model you can use model screws M0,6 and rivets 0,6mm. By using the clamps at RC-models we recommend the soldering of the photo etched parts.

$46.00 *
Delivery weight: 0.1 kg
Product no.: LE-16-AT04

The plate includes the holder for the jack, the heckbox and 2 hinges for the front fenders. Round about 30 screws M0,6 and 20 rivets 0,6mm are neccessary.

$46.00 *
Delivery weight: 0.1 kg


can be shipped within 14 days

Product no.: WI-16-AT05
The plate contains additional parts in combination to the Wiesel basic set WI-16-AT02
$37.00 *
Delivery weight: 80 g


can be shipped within 14 days

Product no.: LE-16-AT05

The plate includes the left and right stowage box and other parts.

$46.00 *
Delivery weight: 0.1 kg


can be shipped within 14 days

Product no.: WI-16-AT06
The plate contains the mud flaps for front and rear, as well as 8 lashing straps for belt buckles. Mud flaps for the front will be bonded to a thin rubber and fastened to model with model screws. The parts can be used both for Wiesel 1 and for Wiesel 2 models.
$17.50 *
Delivery weight: 50 g


can be shipped within 14 days

Product no.: MA-16-AT01

The plate contains: - 6 door hinges - 2 ratchets for lashing straps - 3 canister retaining frame - Steps for cab - Signal flag holder - Wiper Blades - Headlight Guards for SX and HX - 14 truck locking lever - 2 V-shaped reflector holder (HX below the platform) - Flanges for mounting the superstructure on the frame The processing of photo etched parts is not suitable for beginners! Pinning for the etched parts are suitable rivets 0.5 or 0.6 mm thick. For fastening the parts to the model you can use rivets 0.6 and 0.8 mm.

$65.00 *
Delivery weight: 120 g


can be shipped within 14 days

Product no.: MA-16-AT03
$40.00 *
Delivery weight: 80 g


can be shipped within 14 days

Product no.: LU-16-AT02

The plate contains a series of photo-etched parts such as grids,  etc. for detailing the Spähpanzer Luchs from Peter Mueller.

$41.00 *
Delivery weight: 120 g


can be shipped within 14 days

* Prices incl. VAT, plus delivery
1 - 30 of 31 results